This page concerns selling a chiller associated with R-513A in North Carolina, not selling refrigerant as a separate product. The actual refrigerant must be identified from the particular unit or its records when possible; do not assume the charge from a manufacturer name or the appearance of the machine. The buyer handles and pays for refrigerant recovery as part of the equipment purchase and removal.
A clear photograph of the equipment label can help establish whether R-513A is listed for your machine. If the label cannot be read, or the refrigerant status is unknown, say so instead of trying to inspect or open the system yourself. The buyer can review available information alongside the model, condition and site access. An offer is based on the equipment and project details, and the seller does not need to operate the chiller for testing.
Start with the equipment identification
A useful first step is a clear picture of the manufacturer’s plate. It may provide a manufacturer, model, serial number, rated capacity or refrigerant information, but the details shown differ by unit. Include the whole plate before taking a closer image of small lettering. A maintenance record may supply information that is difficult to read. If the plate is damaged or missing, say so rather than guessing. General views of the machine and any available records still give the buyer a way to begin the discussion.
Take photographs that answer practical questions
Wide equipment photographs help establish what is included. A view showing the complete unit helps separate the chiller from nearby equipment. A second set can show the identification plate, visible connections and any detached components that may be part of the sale. Images of the path to the exit are also helpful. Do not move equipment or open electrical enclosures to obtain photographs. If an area cannot be viewed safely, describe the limitation instead.
What if information is missing?
An incomplete file does not prevent an initial conversation. If you cannot identify the tonnage, refrigerant, operating condition or manufacturer, describe what is visible and send any safe photographs you have. The buyer can tell you which additional details would be helpful. Do not assume a refrigerant or a capacity from appearance alone. A tentative description should stay clearly marked as tentative.
Separate observations from assumptions
A seller can distinguish a known fact from an unverified assumption. For example, you may know when a machine was taken out of service without knowing its present operating condition. You may have an older equipment list but no current reading of the nameplate. Explain which information comes from an existing record and which comes from observation. The buyer does not require the seller to start or test the machine and can discuss an offer using the available information.
Describe condition without running the unit
Explain what you know about the machine’s condition. You might know that a chiller was shut down during a replacement project, that it has been idle, or that certain pieces were removed. Those are examples, not requirements. If you do not know why it stopped, say that plainly. The seller does not need to test, start, repair or demonstrate the chiller. The buyer can consider the information supplied and discuss an offer based on the actual circumstances.
Describe where the equipment sits
The chiller’s location matters as much as its label when planning removal. Explain whether it is indoors, outdoors, on a roof or in a lower-level mechanical space. Mention obstructions, narrow paths and any nearby equipment that must remain. Do not assume a truck can reach the same place as the chiller. The buyer can use this information to discuss the practical scope of the disconnect, lift, loading and freight.
Think about the route out
The path from the machine to a loading area is an important project detail. Note visible restrictions such as low clearances, ramps, tight corners or obstructions. If you have reliable dimensions, share them; if not, say the measurements are not yet known. A drawing can supplement photographs of the path. The seller does not need to move or dismantle the chiller to obtain an initial offer discussion.
Include refrigerant in the removal conversation
A nameplate or existing record may help establish what refrigerant a particular chiller uses. If the type or status is unknown, tell the buyer that it is unknown. The buyer handles and pays for refrigerant recovery as part of the equipment removal. Recovery should be discussed along with the rest of the removal scope. EPA explains disposal requirements for chillers in its stationary refrigeration guidance.
Understand the buyer-handled removal scope
Selling an industrial chiller involves both the asset and the practical removal. This buyer handles and pays for refrigerant recovery, electrical disconnect, crane, rigging, loading and freight. Share details about the equipment location, access and any systems that remain so those tasks can be discussed for the particular site. The seller is not expected to run or test the machine. Any site-specific schedule and transaction terms should be agreed before proceeding.
What information supports an offer?
A useful offer discussion brings together the equipment and the site. Share the manufacturer, model, capacity, condition and refrigerant type if known, along with photographs of the equipment and its access route. Mention whether other items are included and when the unit can be released. Estimates should be clearly labeled as estimates. The buyer can review the actual details and discuss a cash offer rather than treating every project as identical.
Request a chiller offer
To discuss your equipment, call (614) 715-3047 or email saleselectricalbuyers@gmail.com. Share whatever nameplate details, condition notes, location and access photographs are available. The buyer can review the information and discuss a cash offer with upfront payment and buyer-paid removal. You do not have to test or run the chiller before contacting the buyer.

